shawnpedersen04:
20140813_185959
shawnpedersen04:
20140813_203231
shawnpedersen04:
20140813_210113
shawnpedersen04:
So many uses for an engine hoist. Now the bandsaw has a nice little stand and I can roll it the H$ll out of my way haha
shawnpedersen04:
Made my first set of v-blocks
shawnpedersen04:
Made my first set of v-blocks
shawnpedersen04:
20141130_204452
shawnpedersen04:
20141130_204500
shawnpedersen04:
20141130_211235
shawnpedersen04:
20141130_211312
shawnpedersen04:
Drilling a 6" hole in granite certainly deserves a beer!
shawnpedersen04:
Extension to get that length...."its all about that length no width.....its all about that length no width".
shawnpedersen04:
Time to work on some inspection and alignment methods now that I have a whipping post.
shawnpedersen04:
Time to work on some inspection and alignment methods now that I have a whipping post.
shawnpedersen04:
Making sure this is dead balls on just for shits and giggles. .0005 from what I can tell with a .001 indicator is not bad! Had to make a few changes to the bottom side to clear the hole by adding a larger recess...worked great. now I can't guarantee the
shawnpedersen04:
New shop toy!
shawnpedersen04:
New shop toy!
shawnpedersen04:
20150125_144158
shawnpedersen04:
Roughing out the rear ISO disc brake jig.
shawnpedersen04:
Mocking up the disc tab and jig. Not feeling good about the lack of metal on metal after its mitered into place with this slack seatstay angle. Thoughts?
shawnpedersen04:
Mocking up the disc tab and jig. Not feeling good about the lack of metal on metal after its mitered into place with this slack seatstay angle. Thoughts?
shawnpedersen04:
Mocking up the disc tab and jig. Not feeling good about the lack of metal on metal after its mitered into place with this slack seatstay angle. Thoughts?
shawnpedersen04:
Finally joined the ranks of Anvil Bikeworks tool ownership!
shawnpedersen04:
Looks like the pre- mitered post mount is ideal for a 160 rotor in this case with a little filing. I'm guessing a 180 you have to go with the unmitered one? Paragon offers two of these two and I can't figutlre out whay the defference is.
shawnpedersen04:
Looks like the pre- mitered post mount is ideal for a 160 rotor in this case with a little filing. I'm guessing a 180 you have to go with the unmitered one? Paragon offers two of these two and I can't figure out whay the difference is.
shawnpedersen04:
Looks like the pre- mitered post mount is ideal for a 160 rotor in this case with a little filing. I'm guessing a 180 you have to go with the unmitered one? Paragon offers two of these two and I can't figutlre out whay the defference is.
shawnpedersen04:
Experimenting with cutting roller dies larger than a .75 ball end mill, custom dia..this setup wasn't even close. Too flexy and interrupted. Ive seen a guy who cuts spheres with a custom ground half round form tool mounted in an r8 collet in the mill.
shawnpedersen04:
Experimenting with cutting roller dies larger than a .75 ball end mill, custom dia..this setup wasn't even close. Too flexy and interrupted. Ive seen a guy who cuts spheres with a custom ground half round form tool mounted in an r8 collet in the mill.
shawnpedersen04:
Loving the mirror finish from my carbide insert face mill.
shawnpedersen04:
Matched v-blocks for holding tapered stays. Works awesome!
